-
Low Pass Filter
Low-pass filters are used to transparently pass high frequency signals while blocking or attenuating frequency components above a specific cutoff frequency.
The low-pass filter has high permeability below the cut-off frequency, that is, signals passing below that frequency will be virtually unaffected. Signals above the cut-off frequency are attenuated or blocked by the filter.
Custom design available upon request.
-
High Pass Filter
High-pass filters are used to pass low-frequency signals transparently while blocking or attenuating frequency components below a specific cutoff frequency.
High-pass filter has a cutoff frequency, also known as a cutoff threshold. This refers to the frequency at which the filter begins to attenuate the low-frequency signal. For example, a 10MHz high-pass filter will block frequency components below 10MHz.
Custom design available upon request.
-
Drop in Circulator
RF drop in circulator is a type of RF device that enables unidirectional transmission of electromagnetic waves, mainly used in radar and microwave multi-channel communication systems. The drop in isolator is connected to the instrument equipment through a ribbon circuit.
The RF drop in circulator belongs to a 3-port microwave device used to control the direction and transmission of signals in RF circuits. The RF drop in circulator is unidirectional, allowing energy to be transmitted clockwise from each port to the next port. These RF circulators have an isolation degree of about 20dB.
-
Drop in Isolator
The drop-in isolator is connected to the instrument equipment through strip line. Drop in isolator usually designed with small dimensions, it is easy to integrate into various devices and saves space. This miniaturized design makes drop in isolators suitable for applications with limited space.Drop in isolator could easy fixed on the PCB board by soldering which make it very convenient to use. The third port of the Drop-in isolator will be equipped with a chip attenuator to attenuate signal energy or chip termination to absorption signal energy. An Drop-in isolator is a protective device used in RF systems, whose main function is to transmit signals in a unidirectional manner to prevent antenna port signals from flowing back to the input (Tx) port.
Frequency range 10MHz to 40GHz,up to 2000W power.
Military, space and commercial applications.
Low insertion loss, high isolation, high power handling.
Custom design available upon request.
-
RFTYT 2 Ways Power Divider
The 2 way power divider is a common microwave device used to evenly distribute input signals to two output ports, and has certain isolation capabilities. It is widely used in wireless communication systems, radar systems, and testing and measurement equipment.
Custom design available upon request.
-
RFTYT 16 Way Power Divider
The 16 ways power divider is an electronic device mainly used to divide the input signal into 16 output signals according to a certain pattern. It is commonly used in fields such as communication systems, radar signal processing, and radio spectrum analysis.
-
Band Stop Filter
Band-stop filters have the ability to block or attenuate signals in a specific frequency range, while signals outside that range remain transparent through.
Band-stop filters have two cutoff frequencies, a low cutoff frequency and a high cutoff frequency, forming a frequency range called the “passband”. Signals in the passband range will be largely unaffected by the filter. Band-stop filters form one or more frequency ranges called “stopbands” outside the passband range. The signal in the stopband range is attenuated or completely blocked by the filter.
-
Chip Termination
Chip Termination is a common form of electronic component packaging, commonly used for surface mount of circuit boards. Chip resistors are one type of resistor used to limit current, regulate circuit impedance, and local voltage.Unlike traditional socket resistors, patch terminal resistors do not need to be connected to the circuit board through sockets, but are directly soldered to the surface of the circuit board. This packaging form helps to improve the compactness, performance, and reliability of circuit boards.
-
Coaxial Mismatch Termination
Mismatch Termination also called mismatch load which is a type of coaxial load.It is a standard mismatch load that can absorb a portion of microwave power and reflect another portion, and create a standing wave of a certain size, mainly used for microwave measurement.
-
Leaded Termination
Leaded Termination is a resistor installed at the end of a circuit, which absorbs signals transmitted in the circuit and prevents signal reflection, thereby affecting the transmission quality of the circuit system.Leaded Terminations are also known as SMD single lead terminal resistors. It is installed at the end of the circuit by welding. The main purpose is to absorb signal waves transmitted to the end of the circuit, prevent signal reflection from affecting the circuit, and ensure the transmission quality of the circuit system.
-
RFTYT 3 Way Power Divider
The 3-way power divider is an important component used in wireless communication systems and RF circuits. It consists of one input port and three output ports, used to allocate input signals to three output ports. It achieves signal separation and power distribution by achieving uniform power distribution and constant phase distribution. It is generally required to have good standing wave performance, high isolation, and good in band flatness.
Custom design available upon request.
-
RFTYT 4 Way Power Divider
The 4-way power divider is a common device used in wireless communication systems, consisting of one input and four output terminals.
