-
Coaxial Fixed Termination (Dummy Load)
Coaxial loads are microwave passive single port devices widely used in microwave circuits and microwave equipment.The coaxial load is assembled by connectors, heat sinks, and built-in resistor chips. According to different frequencies and powers, connectors typically use types such as 2.92, SMA, N, DIN, 4.3-10, etc. The heat sink is designed with corresponding heat dissipation dimensions according to the heat dissipation requirements of different power sizes. The built-in chip adopts a single chip or multiple chipsets according to different frequency and power requirements.
Military, space and commercial applications.
Custom design available upon request.
-
Coaxial Low PIM Termination
Low intermodulation load is a type of coaxial load. The low intermodulation load is designed to solve the problem of passive intermodulation and improve communication quality and efficiency. At present, multi-channel signal transmission is widely used in communication equipment. However, the existing testing load is prone to interference from external conditions, resulting in poor test results. And low intermodulation loads can be used to solve this problem. In addition, it also has the following characteristics of coaxial loads.Coaxial loads are microwave passive single port devices widely used in microwave circuits and microwave equipment.
Military, space and commercial applications.
Custom design available upon request.
-
RFT50-10WT0404
Outline Drawing (Unit: mm/inch) Dimensional tolerance: 5% unless otherwise stated Typical Performance: Installation method Power De-rating Reflow time and temperature diagram P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to their weldability before use. It is recommended to store in vacuum packaging. ■ Drill out the hot hole on the PCB and fill the solder. ■ Reflow welding is ... -
RFT50N-10WT0404
Outline Drawing (Unit: mm/inch) Dimensional tolerance: 5% unless otherwise stated Typical Performance: Installation method Power De-rating Reflow time and temperature diagram P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to their weldability before use. It is recommended to store in vacuum packaging. ■ Drill out the hot hole on the PCB and fill the solder. ■ Reflow welding is ... -
RFT50-100CT6363
Use attention Typical Performance: Installation method Power De-rating Reflow time and temperature diagram P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to their weldability before use. It is recommended to store in vacuum packaging. ■ Drill out the hot hole on the PCB and fill the solder. ■ Reflow welding is preferred for bottom welding, see Introduction to Reflow welding. ■ ... -
RFT50N-60CT0606
Use attention Typical Performance: Installation method Power De-rating Reflow time and temperature diagram P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to their weldability before use. It is recommended to store in vacuum packaging. ■ Drill out the hot hole on the PCB and fill the solder. ■ Reflow welding is preferred for bottom welding, see Introduction to Reflow welding. ■ ... -
RFT50-60CT6363
Use attention Typical Performance: Installation method Power De-rating Reflow time and temperature diagram P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to their weldability before use. It is recommended to store in vacuum packaging. ■ Drill out the hot hole on the PCB and fill the solder. ■ Reflow welding is preferred for bottom welding, see Introduction to Reflow welding. ■ ... -
RFT50N-30CT0606
Use attention Typical Performance: Installation method Power De-rating Reflow time and temperature diagram P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to their weldability before use. It is recommended to store in vacuum packaging. ■ Drill out the hot hole on the PCB and fill the solder. ■ Reflow welding is preferred for bottom welding, see Introduction to Reflow welding. ■ ... -
RFT50-20CT0404
Use attention Typical Performance: Installation method Power De-rating Reflow time and temperature diagram P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to their weldability before use. It is recommended to store in vacuum packaging. ■ Drill out the hot hole on the PCB and fill the solder. ■ Reflow welding is preferred for bottom welding, see Introduction to Reflow welding. ■ ... -
RFT50N-20CT2550
Outline Drawing Typical Performance: Installation method Power De-rating Reflow time and temperature diagram P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to their weldability before use. It is recommended to store in vacuum packaging. ■ Drill out the hot hole on the PCB and fill the solder. ■ Reflow welding is preferred for bottom welding, see Introduction to Reflow welding. ... -
RFT50N-12CT1530
Use attention Typical Performance: Installation method Power De-rating Reflow time and temperature diagram P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to their weldability before use. It is recommended to store in vacuum packaging. ■ Drill out the hot hole on the PCB and fill the solder. ■ Reflow welding is preferred for bottom welding, see Introduction to Reflow welding. ■ ... -
BSF-758M803A-S Band Stop Filter RF Filter
Features and Electrical specifications Model BSF-758M803A-S Rejection band 758-803 MHz Pass band DC~743MHz & 818~1800MHz Insertion Loss ≤2.0dB Rejection ≥40dB VSWR 2.0 Max Rated Power 10 W Impedance 50 Ω Connector Type SMA-F Dimension 121.0×52.0×24.0mm Surface Finishing Black Painting Operating Temperature Ordinary temperature Storage Temperature -55 ~ +85°C Outline Drawing (Unit: mm)
