-
RFTXX-60RM2006F Flanged Resistor RF Resistor
Outline Drawing (Unit: mm) The length of lead wire can meet the customer’s requirements Size Tolerance：5% unless otherwise stated Suggested Stress Relief Methods Power De-rating P/N Designation Use attention ■ After the storage period of newly purchased components exceeds 6 months, attention should be paid to weldability before use. Storage is recommended for storage after vacuum packaging. ■ The best heat conduction is required on the ground surface. ■ Manual welding lead out should... -
Leaded Resistor
Leaded Resistors, also known as SMD two lead resistors, are one of the commonly used passive components in electronic circuits, which have the function of balancing circuits. It achieves stable operation of the circuit by adjusting the resistance value in the circuit to achieve a balanced state of current or voltage. It plays an important role in electronic devices and communication systems.The leaded resistor is a type of resistor without additional flanges, which is usually installed directly on a circuit board through welding or mounting. Compared to resistors with flanges, it does not require special fixing and heat dissipation structures.
Rated power: 10-400W
Substrate materials: BeO, AlN
Nominal resistance value: 100 Ω (10-3000 Ω optional)
Resistance tolerance: ± 5%, ± 2%, ± 1%
Temperature coefficient: ＜ 150ppm/℃
Working temperature: -55~+150 ℃
ROHS standard: Compliant with
Lead length: L as specified in the specification sheet
Custom design available upon request.
-
RFTXX-05CR2550B RF Resistor
Outline Drawing (Unit: mm) Suggested mounting procedures Power De-rating Reflow Profile P/N Designation Use attention ■ After the storage period of newly purchased parts exceeds 6 months, attention shall be paid to the weldability before use. It is recommended to store after vacuum packaging. ■Drill thermal vias through PCB and fill with solder. ■Reflow welding is preferred for welding, see Reflow curve ■ In order to meet the requirements of the drawing, a radiator of sufficient size must b... -
Flanged Resistor
Flanged resistor is one of the commonly used passive components in electronic circuits, which has the function of balancing the circuit.It achieves stable operation of the circuit by adjusting the resistance value in the circuit to achieve a balanced state of current or voltage. It plays an important role in electronic devices and communication systems.In a circuit, when the resistance value is imbalanced, there will be uneven distribution of current or voltage, leading to instability of the circuit. Flanged resistor can balance the distribution of current or voltage by adjusting the resistance in the circuit. The flange balance resistor adjusts the resistance value in the circuit to evenly distribute current or voltage in each branch, thus achieving balanced operation of the circuit.
Rated power: 10-800W
Substrate materials: BeO, AlN, Al2O3
Nominal resistance value: 100 Ω (10-3000 Ω optional)
Resistance tolerance: ± 5%, ± 2%, ± 1%
Temperature coefficient: ＜ 150ppm/℃
Operation temperature: -55~+150 ℃
Flange coating: optional nickel or silver plating
ROHS standard: Compliant with
Lead length: L as specified in the specification sheet
Custom design available upon request.
-
Chip Resistor
Chip resistors are widely used in electronic devices and circuit boards. Its main feature is that it is mounted
directly on the board by surface mount technology (SMT), without the need to pass through perforation or solder pins.Compared to traditional plug-in resistors, chip resistors have a smaller size, resulting in a morecompact board design.
Rated power: 2-30W
Substrate materials: BeO, AlN, Al2O3
Nominal resistance value: 100 Ω (10-3000 Ω optional)
Resistance tolerance: ± 5%, ± 2%, ± 1%
Temperature coefficient: ＜ 150ppm/℃
Operation temperature: -55~+150 ℃
ROHS standard: Compliant with
Custom design available upon request.
-
RFTXX-250RM1313K Leaded Resistor RF Resistor
Suggested mounting procedures Power De-rating Reflow Profile P/N Designation Use attention ■ After the storage period of newly purchased components exceeds 6 months, attention should be paid to weldability before use. Storage is recommended for storage after vacuum packaging. ■Forming a small loop in the tab will act as a strain relief as the heat is dissipated. ■ The best heat conduction is required on the ground surface. ■ Manual welding lead out should be used at or less than 350 degrees ... -
RFTXX-10RM5025C Leaded Resistor RF Resistor
Suggested mounting procedures Power De-rating Reflow Profile P/N Designation Use attention ■ After the storage period of newly purchased components exceeds 6 months, attention should be paid to weldability before use. Storage is recommended for storage after vacuum packaging. ■Forming a small loop in the tab will act as a strain relief as the heat is dissipated. ■ The best heat conduction is required on the ground surface. ■ Manual welding lead out should be used at or less than 350 degrees ... -
RFTXXN-10CR2550C Chip Resistor RF Resistor
Suggested mounting procedures Power De-rating Reflow Profile P/N Designation Use attention ■ After the storage period of newly purchased parts exceeds 6 months, attention shall be paid to the weldability before use. It is recommended to store after vacuum packaging. ■Drill thermal vias through PCB and fill with solder. ■Reflow welding is preferred for welding, see Reflow curve ■ In order to meet the requirements of the drawing, a radiator of sufficient size must be installed. ■ If necessary,... -
RFTXX-20CR2550C Chip Resistor RF Resistor
Suggested mounting procedures Power De-rating Reflow Profile P/N Designation Use attention ■ After the storage period of newly purchased parts exceeds 6 months, attention shall be paid to the weldability before use. It is recommended to store after vacuum packaging. ■Drill thermal vias through PCB and fill with solder. ■Reflow welding is preferred for welding, see Reflow curve ■ In order to meet the requirements of the drawing, a radiator of sufficient size must be installed. ■ If necessary,... -
RFTXX-30CR2550TA Surface Mount Resistor RF Resistor
Suggested mounting procedures Power De-rating Reflow Profile P/N Designation Use attention ■ After the storage period of newly purchased parts exceeds 6 months, attention shall be paid to the weldability before use. It is recommended to store after vacuum packaging. ■Drill thermal vias through PCB and fill with solder. ■Reflow welding is preferred for welding, see Reflow curve ■ In order to meet the requirements of the drawing, a radiator of sufficient size must be installed. ■ If necessary,... -
RFTXX-30CR6363C Surface Mount Resistor RF Resistor
Suggested mounting procedures Power De-rating Reflow Profile P/N Designation Use attention ■ After the storage period of newly purchased parts exceeds 6 months, attention shall be paid to the weldability before use. It is recommended to store after vacuum packaging. ■Drill thermal vias through PCB and fill with solder. ■Reflow welding is preferred for welding, see Reflow curve ■ In order to meet the requirements of the drawing, a radiator of sufficient size must be installed. ■ If necessary,... -
RFTXX-30CR2550W Surface Mount Resistor RF Resistor
Suggested mounting procedures Power De-rating Reflow Profile P/N Designation Use attention ■ After the storage period of newly purchased parts exceeds 6 months, attention shall be paid to the weldability before use. It is recommended to store after vacuum packaging. ■Drill thermal vias through PCB and fill with solder. ■Reflow welding is preferred for welding, see Reflow curve ■ In order to meet the requirements of the drawing, a radiator of sufficient size must be installed. ■ If necessary,...
