-
RFT50N-10CT2550 DC~6.0GHz Chip Termination
Typical Performance: Installation method Power De-rating Reflow time and temperature diagram: P/N Designation Reflow time and temperature diagram ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to their weldability before use. It is recommended to store in vacuum packaging. ■ Drill out the hot hole on the PCB and fill the solder. ■ Reflow welding is preferred for bottom welding, see Introduction to Reflow welding. ■ Add air cooling or water co... -
Coaxial Fixed Termination (Dummy Load)
Coaxial loads are microwave passive single port devices widely used in microwave circuits and microwave equipment.The coaxial load is assembled by connectors, heat sinks, and built-in resistor chips. According to different frequencies and powers, connectors typically use types such as 2.92, SMA, N, DIN, 4.3-10, etc. The heat sink is designed with corresponding heat dissipation dimensions according to the heat dissipation requirements of different power sizes. The built-in chip adopts a single chip or multiple chipsets according to different frequency and power requirements.
Military, space and commercial applications.
Custom design available upon request.
-
Coaxial Low PIM Termination
Low intermodulation load is a type of coaxial load. The low intermodulation load is designed to solve the problem of passive intermodulation and improve communication quality and efficiency. At present, multi-channel signal transmission is widely used in communication equipment. However, the existing testing load is prone to interference from external conditions, resulting in poor test results. And low intermodulation loads can be used to solve this problem. In addition, it also has the following characteristics of coaxial loads.Coaxial loads are microwave passive single port devices widely used in microwave circuits and microwave equipment.
Military, space and commercial applications.
Custom design available upon request.
-
RFT50-60TM1306 DC~6.0GHz RF Termination
Model RFT50-60TM1306(R,L,I) Frequency Range DC~6.0GHz Power 60 W Resistance Range 50 Ω Resistance Tolerance ±5% VSWR 1.25 max Temperature Coefficient <150ppm/℃ Substrate Material BeOO Cap Material Al2O3 Flange Nickel-plated copper Lead 99.99% Sterling silver Resistance Technology Thick Film Operating Temperature -55 to +150°C (See de Power De-rating) Typical Performance: Installation method Power De-rating P/N Designation Matters needing attent... -
RFT50N-05TJ1225 DC~12.0GHz Leaded Termination
Typical Performance: Installation method Power De-rating Reflow time and temperature diagram: P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to their weldability before use. It is recommended to store in vacuum packaging. ■ Drill out the hot hole on the PCB and fill the solder. ■ Reflow welding is preferred for bottom welding, please refer to Reflow introduction ■ The manual welding wire should be use... -
Flanged Termination
Flanged terminations are installed at the end of a circuit, which absorb signals transmitted in the circuit and prevent signal reflection, thereby affecting the transmission quality of the circuit system.The flanged terminal is assembled by welding a single lead terminal resistor with flanges and patches. The flange size is usually designed based on the combination of installation holes and terminal resistance dimensions. Customization can also be made according to the customer’s usage requirements.
-
CT-50W-FH6080-IP65-DINJ-3G DC~3.0GHz Low Intermodulation Termination
Use attention Power De-rating P/N Designation -
RFT50-100CT6363 DC~5.0GHz RF Termination
Typical Performance: Installation method Power De-rating Reflow time and temperature diagram: P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to their weldability before use. It is recommended to store in vacuum packaging. ■ Drill out the hot hole on the PCB and fill the solder. ■ Reflow welding is preferred for bottom welding, please refer to Reflow introduction ■ The manual welding wire should be use... -
RFT50-500WT1313 DC~2.0GHz RF Termination
Typical Performance: Installation method Power De-rating Reflow time and temperature diagram: P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to their weldability before use. It is recommended to store in vacuum packaging. ■ Drill out the hot hole on the PCB and fill the solder. ■ Reflow welding is preferred for bottom welding, please refer to Reflow introduction ■ The manual welding wire should be use... -
RFT50-100TM2595 DC~3.0GHz RF Termination
Typical Performance: Installation method Power De-rating P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to weldability before use. It is recommended to store in vacuum packaging. ■ The ground requires optimal heat transfer. ■ Manual welding should be used under a constant temperature soldering iron of no more than 350 degrees, and the welding time should be controlled within 5 seconds. ■ In order to m... -
MT-100WXX-F1116-NJ-XXG Mismatch Termination
Use attention Power De-rating P/N Designation -
MT-50WXX-F6080-NJ-XXG Mismatch Termination
Use attention Power De-rating P/N Designation
