-
MT-10WXX-R3540-NJ-XXG Mismatch Termination
Use attention Power De-rating P/N Designation -
CT-50W-RX5015-IP65-DINJ 0.35-4G Low Intermodulation Termination
Use attention Power De-rating P/N Designation -
CT-50W-RX5015-IP65-4310J 0.35-4G Low Intermodulation Termination
Use attention Power De-rating P/N Designation -
CT-02W-RA0612-1.85J-67G Coaxial Fixed Termination
Use attention Power De-rating P/N Designation -
CT-02W-RA0612-1.85J-67G Coaxial Fixed Termination
Use attention Power De-rating P/N Designation -
RFT50-20TM7750(R,L) Flanged Termination
Typical Performance: Installation method Power De-rating P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to weldability before use. It is recommended to store in vacuum packaging. ■ The ground requires optimal heat transfer. ■ Manual welding should be used under a constant temperature soldering iron of no more than 350 degrees, and the welding time should be controlled within 5 seconds. ■ In order to m... -
RFT50-10TM7750(R,L) Flanged Termination
Typical Performance: Installation method Power De-rating P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to weldability before use. It is recommended to store in vacuum packaging. ■ The ground requires optimal heat transfer. ■ Manual welding should be used under a constant temperature soldering iron of no more than 350 degrees, and the welding time should be controlled within 5 seconds. ■ In order to m... -
RFT50A-05TM1104 Flanged Termination
Typical Performance: Installation method Power De-rating P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to weldability before use. It is recommended to store in vacuum packaging. ■ The ground requires optimal heat transfer. ■ Manual welding should be used under a constant temperature soldering iron of no more than 350 degrees, and the welding time should be controlled within 5 seconds. ■ In order to m... -
RFT50N-05TJ1225 DC~12.0GHz Leaded Termination
Typical Performance: Installation method Power De-rating Reflow time and temperature diagram: P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to their weldability before use. It is recommended to store in vacuum packaging. ■ Drill out the hot hole on the PCB and fill the solder. ■ Reflow welding is preferred for bottom welding, please refer to Reflow introduction ■ The manual welding wire should be use... -
RFT50-10CT0404 Chip Termination
Typical Performance: Installation method Power De-rating Reflow time and temperature diagram: P/N Designation Matters needing attention ■ After the storage period of newly purchased parts exceeds 6 months, attention should be paid to their weldability before use. It is recommended to store in vacuum packaging. ■ Drill out the hot hole on the PCB and fill the solder. ■ Reflow welding is preferred for bottom welding, see Introduction to Reflow welding. ■ Add air cooling or water cooling if n... -
Chip Termination
Chip Termination is a common form of electronic component packaging, commonly used for surface mount of circuit boards. Chip resistors are one type of resistor used to limit current, regulate circuit impedance, and local voltage.Unlike traditional socket resistors, patch terminal resistors do not need to be connected to the circuit board through sockets, but are directly soldered to the surface of the circuit board. This packaging form helps to improve the compactness, performance, and reliability of circuit boards.
-
Coaxial Mismatch Termination
Mismatch Termination also called mismatch load which is a type of coaxial load.It is a standard mismatch load that can absorb a portion of microwave power and reflect another portion, and create a standing wave of a certain size, mainly used for microwave measurement.
